VW Golf Mk6 2.0 GTI TSI (CCZB) Torque Specifications
Back to Golf Mk6Engine code: CCZB
Power: 155 kW (211hp) @ 5300 rpm
Production years: 2009-2013
Cylinder Head
Renew bolts: Yes
Cylinder head bolts
Tighten bolts 1-5 in the following stages:
40 Nm
90°
90°
Timing chain housing bolts:
8 Nm
90°
Engine Torque Specs
| Component | Torque |
|---|---|
| Main bearings | Renew bolts/nuts: Yes Tighten bolts in the following stages: Tighten bolts 1-10 finger tight. 1-10 = 65 Nm 1-10 = 90° A = 20 Nm A = 90°  |
| Big end bearings | Renew bolts/nuts: Yes Stage 1: 30 Nm M9=45 Nm Stage 2: 90° |
| Oil pump to cylinder block | 9 Nm M8=20 Nm |
| Sump drain bolt | 30 Nm |
| Flywheel/driveplate | 60 Nm + 90° (Use new nuts/bolts) |
| Clutch pressure plate | 13 Nm M7=20 Nm |
| Crankshaft pulley/damper centre bolt | 150 Nm + 90° (Use new nuts/bolts) |
| Camshaft carrier/cap | 8 Nm + 90° (Use new nuts/bolts) Use new bolts. Tighten all bolts in rows 1-6 to 8 Nm. Tighten all bolts in rows 1-6 a further 90°. |
| Inlet manifold to cylinder head | 1)3 Nm 2)9 Nm |
| Exhaust downpipe to manifold | 40 Nm (Use new nuts/bolts coated with high temperature lubricant) |
| Spark plugs | 25 Nm |
| Crankshaft position (CKP) sensor/engine speed (RPM) sensor | 10 Nm |
| Camshaft position (CMP) sensor | 10 Nm |
| Lambda sensor (Oxygen) | 55 Nm |
| Knock sensor (KS) | 20 Nm |
| Engine oil pressure switch | 20 Nm |
| Oil filter | 20 Nm |
Chassis Tightening Torques
| Component | Torque |
|---|---|
| Front hub | Use new bolts. 12 point bolt with knurled underside: Tighten to 70 Nm with wheels off the ground. Lower car to the ground and tighten a further 90°. 12 point bolt with plain underside: Tighten to 200 Nm with wheels off the ground. Lower car to the ground and tighten a further 90°.  |
| Front hub - wheel bearing housing bolts | 70 Nm + 90° (Use new nuts/bolts) |
| Rear hub | 200 Nm + 180° (Use new nuts/bolts) |
| Steering wheel | 30 Nm + 90° (Use new nuts/bolts) |
| Steering rack/box mounting | 50 Nm + 90° (Use new nuts/bolts) |
| Steering track rod end | 20 Nm + 90° (Use new nuts/bolts) |
| Brake disc to hub (Front) | 4 Nm |
| Brake caliper to carrier (Front) | 30 Nm |
| Brake caliper/carrier to hub (Front) | Brake caliper to hub FS III caliper (PR No. 1ZF/1ZM/1ZQ) = 30 Nm Caliper carrier to hub FN3 caliper (PR No. 1ZE/1ZP/1ZJ/1ZD/1LJ/1LL/1LV/1ZA/1ZB) = 190 Nm FNR-G caliper (PR No. 1ZK): 15 Nm 200 Nm |
| Brake disc to hub (Rear) | 4 Nm |
| Brake caliper to carrier (Rear) | 35 Nm (Use new nuts/bolts) |
| Brake caliper/carrier to hub (Rear) | 90 Nm + 90° (Use new nuts/bolts) |
| Back plate to hub (Rear) | 12 Nm |
| ABS sensor (Front) | 8 Nm |
| ABS sensor (Rear) | 8 Nm |
| Road wheels | 120 Nm (Do NOT lubricate bolts. Lightly coat mating surfaces between wheel centre hole and hub) |
Disclaimer
The information provided on this website is for general informational purposes only. While we strive to ensure the accuracy and currency of the data, we make no representations or warranties of any kind, express or implied, about the completeness, accuracy, reliability, suitability, or availability with respect to the website or the information, products, services, or related graphics contained on the website for any purpose. Any reliance you place on such information is therefore strictly at your own risk. In no event will we be liable for any loss or damage including without limitation, indirect or consequential loss or damage, or any loss or damage whatsoever arising from loss of data or profits arising out of, or in connection with, the use of this website. Always consult your vehicle's service manual or a qualified professional for critical applications.