VW Golf Mk7 2.0 GTI Clubsport S (CJXG) Torque Specifications
Back to Golf Mk7Engine code: CJXG
Power: 228 kW (310hp) @ 5800 rpm
Production years: 2016-2017
Cylinder Head
Renew bolts: Yes
Tighten: 40 Nm
Tighten: 90°
Tighten: 90°
Tighten: M6=4 Nm+90°
Engine Torque Specs
| Component | Torque |
|---|---|
| Sump drain bolt | 30 Nm (Replace factory fitted sump drain bolt at first oil change with type with replaceable seal.) |
| Flywheel/driveplate | 60 Nm + 90°/- (Use new nuts/bolts) |
| Clutch pressure plate | M6=13 Nm M7=20 Nm |
| Crankshaft pulley/damper centre bolt | 150 Nm + 90° (Use new nuts/bolts) |
| Camshaft carrier/cap | Apply a 2,0-3,0 mm diameter bead of sealant to mating surface of camshaft cover fig 1. Assemble components within 5 minutes. Excess sealant can cause engine damage. Move exhaust camshaft sliding cam units into installation position before fitting camshaft cover fig 2. Use new bolts. Tighten all bolts in rows 1-6 to 8 Nm. Tighten all bolts in rows 1-6 a further 90°. fig 3  |
| Spark plugs | 30 Nm |
| Oil filter | 25 Nm |
Chassis Tightening Torques
| Component | Torque |
|---|---|
| Front hub | Use new bolt. Tighten to 200 Nm with wheels off the ground. Lower car to the ground and tighten a further 90°. |
| Rear hub | 200 Nm + 90° (Use new nuts/bolts) |
| Rear hub - wheel bearing housing bolts | Use new bolts. Torsion beam suspension (FWD): Stub axle: 30 Nm 90° |
| Steering wheel | 30 Nm + 90° (Use new nuts/bolts) |
| Steering rack/box mounting | 70 Nm + 90° (Use new nuts/bolts) |
| Steering track rod end | 20 Nm + 90° (Use new nuts/bolts) |
| Brake disc to hub (Front) | 8 Nm |
| Brake caliper to carrier (Front) | 35 Nm (Use new nuts/bolts) |
| Brake caliper/carrier to hub (Front) | Brake caliper to hub FS III caliper (PR No. 1ZF) = 30 Nm Caliper carrier to hub PC57/C60 caliper (PR No. 1ZE/1ZP/1ZA/1ZD/1ZB/1LJ/1LM) = 200 Nm PC60 caliper (PR No. 1LK) = 200 Nm |
| Brake disc to hub (Rear) | 8 Nm |
| Brake caliper to carrier (Rear) | 35 Nm |
| Brake caliper/carrier to hub (Rear) | 90 Nm + 90° (Use new nuts/bolts) |
| Back plate to hub (Rear) | 12 Nm |
| ABS sensor (Front) | 8 Nm (Coat ABS wheel speed sensor with high temperature lubricant G 052 112.) |
| ABS sensor (Rear) | 8 Nm (Coat ABS wheel speed sensor with high temperature lubricant G 052 112.) |
| Road wheels | 120 Nm (Do NOT lubricate bolts. Lightly coat mating surfaces between wheel centre hole and hub (use spray wax).) |
Disclaimer
The information provided on this website is for general informational purposes only. While we strive to ensure the accuracy and currency of the data, we make no representations or warranties of any kind, express or implied, about the completeness, accuracy, reliability, suitability, or availability with respect to the website or the information, products, services, or related graphics contained on the website for any purpose. Any reliance you place on such information is therefore strictly at your own risk. In no event will we be liable for any loss or damage including without limitation, indirect or consequential loss or damage, or any loss or damage whatsoever arising from loss of data or profits arising out of, or in connection with, the use of this website. Always consult your vehicle's service manual or a qualified professional for critical applications.